Hydroflo Controls – Joh Clouth ceramic blades

	About Hydroflo	News & Technical Information	A Word from the Expert	Contact Information		Site Map

PULP AND PAPER

	JOH. CLOUTH PRODUCTS		Back to JC Section Page

JOH. CLOUTH PRODUCTS

Doctor Blades

Doctor Blade Holders

Tubes

System Accessories

FOR COATING

CERAMIC BLADES

FOR CREPING

	CERADIA®-100				CREPING BLADE 850 in carbon steel
	Stiff blade, Bent blade or Double angle Blade with ceramic tip				MATERIAL - Carbon steel (0.85%), hardness approx. 46-48 HRC (approx. 437-466 HB)
	MATERIAL -

					KEY FEATURES -
	. Primary material: Carbon steel (1%), stainless steel . Coating: Ceramic base on Al-TiO2 . Coating hardness: approx. 1100 HV0.3 . Coating colour: Light grey				. Continuous length to individual specification . Hardened, tempered, plain ground and straight . Bevel 3° - 90° . Straightness tolerance max. 0.2 mm over 1000 mm . Land of 0.1 mm - 1.0 mm
	KEY FEATURES - . Continuous length to individual specification . Hardened, tempered, blue-grey, straight adjusted . Individual bevel according customer requirement . Straightness tolerance max. variation 0.05 mm over 1000 mm

	CERADIA®-200				CREPING BLADE 850 EH - Carbon steel extra hard
	Stiff blade, Bent blade or Double angle Blade with wear resistant ceramic tip				MATERIAL - Carbon steel (1%), hardness approx. 52-55 HRC (approx. 523-570 HB)
	MATERIAL -				KEY FEATURES -
	. Primary material: Carbon steel (1%), stainless steel . Coating: Ceramic base on Al-TiO2 . Coating hardness: approx. 1100 HV0.3 . Coating colour: Light grey				. Continuous length to individual specification . Hardened, tempered, plain ground and straight . Bevel 3° - 90° . Straightness tolerance max. 0.2 mm over 1000 mm . Land of 0.1 mm - 1.0 mm
	KEY FEATURES - . Continuous length to individual specification . Hardened, tempered, blue-grey, straight adjusted . Individual bevel according customer requirement . Straightness tolerance max. variation 0.05 mm over 1000 mm

	COATER BLADES IN CARBON STEEL				PHOSPHORBRONZE
	MATERIAL - Carbon steel, hardness approx. 52-55 HRC (approx. 523-570 HB)				MATERIAL - Phosphorbronze, hardness approx. 200-220 HB
	KEY FEATURES - . Continuous length to individual specification . Hardened, tempered, blue-grey or blue polished, even and straight . Bevel 3° - 90° . Straightness tolerance max. 0.05 mm over 1000 mm . Quick-Start Bevel 25° - 55° . Land of 0.02 mm - 0.55 mm depending on material thickness				KEY FEATURES - . Continuous length to individual specification . Hardened, tempered, plain ground and straight . Bevel 3° - 90° . Straightness tolerance max. 0.2 mm over 1000 mm . Land of 0.1 mm - 1.0 mm

	COATER BLADES IN STAINLESS STEEL
	MATERIAL - Stainless steel 18/8, hardness approx. 46-48 HRC (approx. 437-466 HB)
	KEY FEATURES - . Continuous length to individual specification . Blank ground and polished, even and straight . Bevel 3° - 90° . Straightness tolerance max. 0.05 mm over 1000 mm . Quick-Start Bevel 25° - 55° . Land of 0.02 mm - 0.55 mm depending on material thickness

	FLO-CLEAN IN CARBON STEEL
	MATERIAL - Carbon steel, hardness approx. 52-55 HRC (approx. 523-570 HB)
	KEY FEATURES - . Continuous length to individual specification . Hardened, tempered, blue-grey or blue polished, even and straight . Straightness tolerance max. 0.05 mm over 1000 mm

	FLO-CLEAN IN STAINLESS STEEL
	MATERIAL - Stainless steel, hardness approx. 46-48 HRC (approx. 437-466 HB)
	KEY FEATURES - . Continuous length to individual specification . Blank ground and polished, even and straight . Straightness tolerance max. 0.05 mm over 1000 mm

	SUPPORTING BLADE IN CARBON STEEL
	MATERIAL - Carbon steel C=1%, hardness approx. 52-55 HRC (approx. 523-570 HB)
	KEY FEATURES - . Continuous length to individual specification . Hardened, tempered, blue-grey or blue polished, even and straight . Straightness tolerance max. 0.05 mm over 1000 mm

	NIP PLATE in carbon steel or in stainless steel
	MATERIAL - Carbon steel or stainless steel 18/8, hardness approx. 46-48 HRC (approx. 437-466 HB)
	KEY FEATURES - . Fully deburred . (Hardened,) even and straight . Punched or Laser-cut